Overview — Zamp 30 Amp 5-Stage PWM Charge Controller
The Zamp Solar 30-amp charge controller can regulate up to 510 watts and is compatible with Lithium, Gel, AGM, Conventional lead-acid (wet) batteries, and LTO.
Protects and Regulates
All our charge controllers use pulse width modulation (PWM) and five stages of charging to regulate the flow the electricity to your battery. This protects your battery from overcharging, expands your battery’s lifespan, and keeps your panel safe from back flow electrical currents, among many other protections and benefits.
Monitors and Indicates
Its large digital display lets you monitor battery voltage, charging current, charging capacity (amps per hour), battery types, full charge, and system faults. Colored LEDs indicate operational status and battery conditions.
Flexible and Customizable
Our 30-amp charge controller is weather resistant and can be surface-mounted on your wall, or flush-mounted inside the wall. It is compatible with our battery temperature cable and with our remote LCD display that lets you keep tabs on your power from wherever it's most convenient for you.
30-Amp Charge Controller Specs:
Watts: (12V) 510 - (24V) 1,020
Lithium Compatibility: Yes
Remote Display Compatible: Yes
Battery Temperature Sensor Compatible: Yes
Mounting Options: Surface or Flush Mount
Resources — Zamp 30 Amp 5-Stage PWM Charge Controller
Warranty — Zamp 30 Amp 5-Stage PWM Charge Controller
✓ OffGrid Harbor is an Authorized Zamp Solar Dealer
✓ Includes all applicable Manufacterer Warranties
✓ Ships direct from manufacterer
✓ Additional Lifetime support from our specialists
FAQs — Zamp 30 Amp 5-Stage PWM Charge Controller
Q: Can I connect two charge controllers to the same battery bank (e.g. combine a roof mount system and a portable kit)?
Answer: Yes, two independent charge controllers can be connected directly to the battery as long as both controllers are set to the same battery type. The charge controllers will not work properly if wired in series, one to the other.
Q: Is the Zamp Solar port reverse polarity?
Answer: No, but they are different from other brands of solar ports because all of our SAE plugs are polarity-protected for safety reasons. That means the positive pin on all of our SAE plugs is set back and covered to prevent accidental contact that could damage your panel, short your battery, or give you a pretty nasty shock. So, because of the polarity protection on our plugs, Zamp Solar ports are only compatible with Zamp Solar SAE plugs.
Q: What does the b01 601 error message on my charge controller mean?
Answer: This common error code means the charge controller can’t see the battery bank. The most common cause of this is a bad connection between the charge controller and the battery bank
Q: Why isn’t my solar system charging my battery?
Answer: When a solar system isn’t working, the most common culprit is a wiring problem. Our troubleshooting document can help you identify the disconnect and get it fixed. If you’re still having issues, please contact us for further assistance.
Q: What batteries should I use?
Answer: Any type of 12-volt deep cycle battery (lithium, gel, AGM, conventional lead-acid (wet), and calcium) will work with your Zamp Solar system. If you choose to go with two 6-volt batteries, make sure that you use two of them wired in series to create a 12-volt battery bank.
Q: What size kit do I need to power my RV?
Answer: Everybody’s needs are different, but we can certainly provide some insight into what size solar kit typically works for various sizes of RVs. Check out our infographic to see which of our kits might work best for you.
Q: I have a Zamp Solar Ready sticker on the side of my RV, what does that mean?
Answer: If an RV is “solar ready,”it means that the RV came pre-wired for our solar products with either a 3-port roof cap, a single port roof cap, or a side-wall port. However, each manufacturer does it slightly differently—some include full wiring, while others only wire from the roof to the batteries.